USBC to HDMI Extender Kit Ideal for Digital Signage in Schools, Restaurants and Lecture Halls This complete transmitter and receiver system is recommended for video presentations in conference rooms, schools, trade shows, meeting facilities, houses of worship, retail settings, hotels and other digital signage applications where the source and display are farther apart than conventional A/V cables allow. Extends a 4K A/V Transmission up to 230 ft....or More The B127A1A1BCBH extends 4K signals from a USBC source device to an HDMI display up to 230 feet away via usersupplied Cat6 cabling. By adding a Tripp Lite B127A010H HDMI repeater or B127A110BH transceiver (sold separately) to the application, you can extend the signal up to 400 or 460 feet, respectively. Dip Switch Extends Your Choice of Either USB or IR. The DIP switches on both the transmitter and receiver can be adjusted to let you choose from the USB 1.1 or bidirectional IR functions. Choose to either control the source device via keyboard and mouse or IR remote control from the display end of the installation. Only one function can be extended at a time. Transmits CrystalClear 4K Video with MultiChannel Audio and 4:4:4 Color The B127A1A1BCBH supports Ultra HD resolutions up to 3840 x 2160 (4K x 2K) at 60 Hz, as specified by HDMI 2.0, with full, rich uncompressed DTSHD, Dolby TrueHD and 7.1channel digital audio. HDCP 2.2 compliance allows you to stream 4K Amazon and Netflix content with no complications. This extender kit also supports 4:4:4 chroma subsampling for toplevel PC gaming or using your HDTV as a PC monitor. Builtin equalization allows you to finetune the image quality at the remote display. Local HDMI Port on Transmitter Supports 4K @ 60 Hz Resolution To monitor the video signal being extended to the receiver, connect a 4K display to the transmitter’s local HDMI port with a usersupplied HDMI cable. This port does not support multiresolution capabilities, so the connected monitor must also support 4K/60 Hz to function properly. BuiltIn PoC Technology Provides Power to Avoid Bulky External Power Bricks After you connect the included external power supply to either the transmitter or receiver, Power over Cable (PoC) technology powers the opposite unit over Cat6 cable. LEDs on both the transmitter and receiver will light up to indicate the system is receiving power and a signal is being transmitted. PoC lets you avoid the hassle of a bulky power brick and gives you the freedom to place one unit where needed without worrying about finding a nearby AC outlet. PD 3.0 Charging Port Powers the Source Device to Maintain a Clear Signal The USBC Power Delivery port provides up to 20V 5A (90W, with 10W dedicated to the unit’s power reserve) for powering the connected source device when using an EMark USBC cable (such as Tripp Lite’s U040C13C5A). With a nonEMark cable, the USBC PD 3.0 port provides up to 20V 3A (50W, with 10W to the power reserve). The other USBC port connects the transmitter to the source. PlugandPlay Operation for Quick Setup and Immediate Use The included transmitter and receiver units work right out of the box with no software required. Mounting hardware is included for installing both units on a wall, pole or 19inch rack. Connect the transmitter to the source with a usersupplied USBC cable. Then, connect the receiver to the display with a usersupplied HDMI cable (such as Tripp Lite’s P568 or P569Series). Finally, connect the two units with usersupplied Cat6 patch cable (such as Tripp Lite N202Series). TAACompliant for GSA Schedule Purchases The B127A1A1BCBH is compliant with the Federal Trade Agreements Act (TAA), which makes it eligible for GSA (General Services Administration) Schedule and other federal procurement contracts.
Brand
- Tripp Lite
